This is the homemade cannabis oil recipe that people are using to treat cancer!

The re-entrance of cannabis into the primary stream awareness has begun the back of revelations that the herb has huge cancer curing capacity. The cannabinoids, particles within the plant, go into the body on usage and bind with receptors that are currently in place.

Cannabis oil

Our bodies are made to handle this stuff.

The resulting endocannabinoids that are released by the body carry out a range of positive results, consisting of regulation of cell growth. The fact that we have receptors for the chemical appears to show that we are evolved to eat the plant and the favorable effect the chemicals have on our system further implies that.

One of the most popular ways to consume the plant is by smoking it, but the excess chemicals from the fire can trigger unneeded issue. Rick Simpson, a leader in the medical cannabis field, has mastered the art of marijuana oil production and released his strategy to the world for free.

You can support Rick on his site; here is a condensed version of the process of making hemp oil.

Start with one ounce of dried herb. One ounce will normally produce 3-4 grams of oil, although the amount of oil produced per ounce will vary pressure to pressure. A pound of dried product will yield about two ounces of high quality oil.

CRUCIAL: These directions are directly summarized from Rick Simpson’s website. Be REALLY careful when boiling solvent off, the fumes are very combustible. PREVENT cigarette smoking, triggers, stove-tops and red hot heating aspects. Set up a fan to blow fumes far from the pot, and set up in a well-ventilated area for whole process.

1. Place the completely dry product in a plastic pail.

2. Dampen the material with the solvent you are utilizing. Lots of solvents can be utilized [solvent-free choice] You can use pure naphtha, ether, butane, 99% isopropyl alcohol, and even water. 2 gallons of solvent is required to draw out the THC from one pound, and 500 ml suffices for an ounce.

3. Crush the plant material using a stick of tidy, unattended wood or other similar device. Although the material will be damp, it will still be relatively simple to squash up due to the fact that it is so dry.

4. Continue to crush the product with the stick, while adding solvent until the plant material is entirely covered and soaked. Remain stirring the mixture for about 3 minutes. As you do this, the THC is liquified off the material into the solvent.

5. Pour the solvent oil mix off the plant product into another bucket. At this point you have stripped the material of about 80% of its THC.

6. Second wash: once again include solvent to the mix and work for another three minutes to extract the staying THC.

7. Pour this solvent oil mix into the container containing the very first mix that was previously put out.

8. Discard the twice washed plant material.

9. Pour the solvent oil mixture through a coffee filter into a clean container

10. Boil the solvent off: a rice cooker will boil the solvent off well, and will hold over a half gallon of solvent mix. CARE: prevent stove-tops, red hot components, triggers, cigarettes and open flames as the fumes are exceptionally combustible.

11. Include solvent to rice cooker up until it has to do with 3/4 complete and switch on HIGH heat. Make sure you remain in a well-ventilated location and set up a fan to carry the solvent fumes away. Continue to include mixture to cooker as solvent evaporates up until you have actually added all of it to the cooker.

12. As the level in the rice cooker decreases for the last time, add a couple of drops of water (about 10 drops of water for a pound of dry product). This will assist to launch the solvent residue, and protect the oil from too much heat.

13. When there has to do with one inch of solvent-water mix in the rice cooker, placed on your oven mitts and select the system up and swirl the contents up until the solvent has actually completed boiling off.

14. When the solvent has actually been boiled off, turn the cooker to LOW heat. At no point must the oil ever reach over 290 degrees F or 140 degrees C.

15. Keep your oven mitts on and eliminate the pot containing the oil from the rice cooker. Gently pour the oil into a stainless steel container.

16. Location the stainless-steel container in a dehydrator, or put it on a mild heating device such as a coffee warmer. It might take a few hours however the water and unpredictable terpenes will be vaporized from the oil. When there is no more any surface activity on the oil, it is ready for use.

17. Suck the oil up in a plastic syringe, or in any other container you see fit. A syringe will make the oil easy to give. When the oil cools completely it will have the consistency of thick grease.